- 1 -Page 1 of 37 GPS VT-300. Automatic Vehicle Locator User Manual. Version PDF

Please download to get full document.

View again

of 37
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Document Description
- 1 -Page 1 of GPS VT-300 Automatic Vehicle Locator User Manual Version Page 2 of Table of Contents I. Hardware installation...5 A. working directions..5 B. System introduction 6 C. Wiring Installation
Document Share
Document Transcript
- 1 -Page 1 of GPS VT-300 Automatic Vehicle Locator User Manual Version 1.3 - 2 -Page 2 of Table of Contents I. Hardware installation...5 A. working directions..5 B. System introduction 6 C. Wiring Installation 7 1. Product Parts List Precaution before Installation Panel Description Installation Power Charging Wiring Description Description of the LED Indicators Inspection Item after Installation...13 D. Operating Instructions.13 E. Hardware Specification 17 II. Track GPS Location by Google Earth maps...18 III. DIY!!! Build your control center system on your PC - 3 -Page 3 of I Hardware installation A. Working Directions Thank you for your purchase of VT300 Automatic Vehicle Tracker. In order to realize the full functions of this product, please read this manual carefully before starting to use the product. 1. This product can only be maintained and repaired by qualified professional service personnel. If you detach this product for maintenance or repair, your warranty will be invalidated. 2. When connecting the other devices, read carefully their instruction manuals,so as to carry out correct installation; do not connect incompatible device. 3. Please use genuine original parts and qualified batteries and peripheral equipments, so as to avoid damage to this product. 4. As this product is a high-tech product, please read carefully this manual before starting to use the product, so as to avoid inappropriate operation. 5. Drivers should not operate this product while driving a vehicle, thereby,affecting safe driving. 6. This product can work properly only when GSM communication is in good condition. 7. Please reduce electromagnetic wave interference to the product; and use it properly. 8. GPS communication is liable to be affected by environmental shielding; may fail to carry out positioning during certain circumstances. It will resume the positioning function as soon as it leaves the shielding environment. This is normal. Please do not worry when encountering such problem. 9. Each signal sent out from the system will be confirmed for successful transmission in the base station of the mobile operator. However, if system stoppage occurs or if the mobile telephone is preset to a switch off state by the customer, it cannot ensure successful transmission. 10. For safety reason, do not tell the other people your VT300 mobile number,without taking precautions. Otherwise, your privacy may be compromised along with other safety problem. - 4 -Page 4 of B. System Introduction VT300 is a high-tech product through cooperation with mobile operators. It combines GPS Global Positioning System and GSM/GPRS communication system, which can clearly inform you the position & situation of your car. GPS is the abbreviation for Global Positioning System, which based on 24 position location satellites around the earth orbit. Their locating precision can be kept within 10 to 15 meters. GSM is the second digital mobile communication system (GPRS, second and fifth digital mobile communication system), and at present it is the mobile communication system that has the largest coverage and owns the most number of users. This product combines GPS and GSM/GPRS technologies together. It uses GPS system to locate your car, and sends the position/ situation report back to you via GSM/GPRS communication system. With a delicate microphone, you can monitor the present situation in your car from a faraway place. You can use the telephone remote control function to set monitoring mode, which will report the situation of your car to you periodically. - 5 -Page 5 of Following are the function descriptions for the VT300 products. GPS Position Tracking Function With this function, the vehicle owner will be able to know the geographic coordinates, direction, and other related information of the car anytime in any place. The report methods can be via SMS short message service. You can also select a one time report or continuous report (tracking function). C. Wiring Installation 1. Product Parts List AVL Unit - 6 -Page 6 of GPS Antenna GSM Antenna Car Charger Lighter Socket - 7 -Page 7 of 2. Precaution before Installation Check if all the parts are included. Prepare a SIM card for GSM communication. Use some other mobile phone to confirm that the PIN code has not been set, and that it can dial out and receive telephone calls without problem. Before install the SIM card, make sure to cut off power from the AVL unit. The correct installation method is to push the tray completely into the AVL unit, until you feel it is hooked by something. Find a suitable place inside the car for installing the unit. Check if all the wiring has been connected correctly; then connect the AVL unit to the power source. - 8 -Page 8 of 3. Panel Description GPS antenna GPM antenna Power Led SIM card connector - 9 -Page 9 of 4.INSTALLATION Step 1: Install GSM Antenna * Connect the GSM Antenna to the unit. * Fasten the connection by turning the screw in the bottom. Please do not swing round the antenna itself. Step 2: Install SIM Card - 10 -Page 10 of (1) Unscrew and remove the front cover of your locator. (2) Insert the SIM card by sliding it into the card holder slot, with the chip module facing to the connectors on PCB, as direction shown in the picture. (3) Put back the front cover and screw it up. Make sure to turn off the power before install the SIM card. Make sure to deactivate the PIN code, so that the SIM card can operate without PIN protection. Before install the SIM card to the GPS Tracker, please use a mobile phone to make sure the SIM card can make & receive phone calls without problem. Before install the SIM card to the GPS Tracker, please use a mobile phone to empty the SMS storage of the SIM card. Step 3: Connect GSM Antenna Page 11 of Step 4: Connect GPS Antenna - 12 -Page 12 of GPS antenna is used to receive satellite signals in the sky. It should be positioned at a place where it will have an unobstructed view of the sky. The ideal location is top of the dashboard or close to the rear window of the car. GPS antenna can pick up signals through glass and plastic, but will not see the sky through metal or other conductive surfaces. To avoid distractions of GPS signal, make sure the antenna is not covered or shielded by any object containing metal, such as the metallic windshield. If your car is with metallic windshield, please cut a hole on the windshield above the place where you put the GPS antenna, so that the antenna can receive the GPS signals. Step 4: Connect power charging VT300 connects to the car charger lighter socket Page 13 of GSM Antenna Connect Blue line and Green line Power switch AVL Black line link to ground Red line link to positive VCC + -- Car Battery GPS Antenna Other Lines: - 14 -Page 14 of Pin Colour function 1 Red DC IN ( power input ) Input voltage : 9V~35V Suggested : 12V 2 Black GND 3 white IN :Control signal input ( for example, you can input one pressing key single) See following application example 4 Blue Out :Control signal output See following application example 5 Yellow SW1 : Connect the power switch 6 Yellow SW2 : Connect the power switch Pin IN and OUT1 application example: White line link to One SOS key Blue line link to one Relay to cut down the car motor or other power VCC Relay Motor - 15 -Page 15 of OUT1 Pin operation : (1) connect the relay as above picture show, and calculate the correct VCC value according to the relay parameter to make sure to following requirement: Out1 Input voltage Out1 input current Must 50V Must 500mA (2) Send one following SMS to give the relay the current to drive it : W******,020,1,1 (3) Send one following SMS to cut off the current of the relay.: W******,020,1,1 IN Pin operation: (1) connect one SOS key as above picture show. (2) Send one following SMS to set SOS alarm phone number of aid canter W******,003,1,1,Tel number Tel number: the SOS alarm phone number of aid centre, like (3) When someone press the SOS key, the aid centre will receive the SOS Alarm SMS ---- SOS Alarm 6. Wiring Description Page 16 of Connect the wiring correctly. The AVL unit should be connected to power source, after all the wiring work has been completed and checked. GPS antenna is used to receive satellite signals in the sky. It should be fixed to face the sky; and should not be covered or shielded by any object containing metal, such as the metallic windshield. Wiring connections must be firm and reliable; and the joints should be wrapped with insulating tape tightly. The unused electrical wire should be properly insulated. 7. Description of the LED Indicators Flash Constant Glow Constant Dark SYSTEM STATE (RED LAMP) Work normally Charging In trouble or no power 8. Inspection Item after Installation After connected to the power source, the RED LED Indicator should be constant glow or Flash. D. Operating Instructions Page 17 of 1. Position Report Function No matter where you are, when you want to know the position of your vehicle, send a SMS message or make a telephone call to the VT300; it will report its location back to you by SMS. Edit a message as following format, then send it to VT300: Format: W+Password+, +000 ( init password is : ) For example: W000000,000 - 18 -Page 18 of The VT300 send back one SMS,which including the position information Position Data means : Longitude = 114 degree - 04 cent second Latitude = 22 degree - 32 cent second Tips: Apply for one position service by another easier way: (a) Make a cell phone call to VT300 (b) After listening the ring of VT300, hold off the dialup (c) Then, after 10 second, the cell phone will receive the Position SMS. 2. Tracking Function Page 19 of Tracking report function can be turned on or off according to the requirements of the user. Tracking function will continually report vehicle position until it get stop command.in this tracking module, VT300 will send one position message at a preset time interval. Step1.Edit a message as following format, then send it to VT300: W+Password+,+002,+XXX (Note : XXX Unit: preset minute interval -- if XXX=000 it is STOP tracking ) For example : W000000,002,005 (its means is VT300 will send Position Data every 5 minute.) - 20 -Page 20 of Step2. VT300 will send back one SMS-----Set Time (preset time interval) OK. In this example, the SMS is Set Time (005 Min) OK This SMS means that VT300 is in tracking mode now and preset time interval is 5 minutes. Step3. VT300 will send back position SMS at preset time interval. In this example, the SMS will send back at preset time interval :5 minutes 3. Stop tracking function Page 21 of This function is used to turn off tracking report function. Edit a message as following format, then send it to VT300: Format: W+passwaord+,+002+,+000 For example : W000000,002,000 The VT300 will reply by one SMS-----Stop Timer OK. This message means tracking report function is turned off. E. Hardware Specifications Page 22 of Feature Characteristics Power Supply +9V to +40V Power Consumption For Active mode(peak) 1.0A VBATT Active mode(avg.) 300mA Idle mode 50mA Sleep mode 5mA Operating Temperature -20 to +60 Range Storage Temperature -20 to +70 Range Humidity Up to 75% non-codensing External Antenna Connected via the 50Ω coax connector External SIM Card Connected via SIM Card connector SIM card type 3V Transmit Power Class 4(2W) for E-GSM 900 and 850 Class 1(1W) for DCS 1800 Class 1(1W) for PCS 1900 Sensitivity -104 dbm minimum for E-GSM 900 and dbm minimum for DCS dbm minimum for PCS 1900 Speech Codec Triple rate Codec: Half rate ETS Full rate ETS Enhance Full rate-ets 06.50/06.06/06.08 GPRS Multi-slot Class 8(4Rx, 1Tx, 5 slot Max.) Support all 4 coding schemes(cs-1, CS- 2, CS-3 and CS-4) Maximum download speed is 85.6kbps Maximum upload speed is 21.4kbps Circuit-Switched Data 14.4kbps Rate Interface Full duplex 3V CMOS-level Serial interface for AT commands protocol Dimensions 11.4 x 8.0 x 2.0 (cm) - 23 -Page 23 of II. Track GPS Location by Google Earth/Maps You can get the latitude & longitude data by sending W+Password+, +000 SMS command Code to the GPS Tracker VT300. Input the received latitude & longitude data to Google Earth (from earth.google.com) or Google Maps (maps.google.com), then you can find the position fix in the map. Please find below the example. 1) Send a SMS Command Code W+Password+, +000 to the GPS Tracker VT300.For example,the init password is : ,the SMS command code is: W000000,000 2) GPS Tracker will send back some data similar to below, with latitude/ longitude figures. - 24 -Page 24 of 3) Start the Google Earth software.(for more information about Google Earth software, please refer to Input the latitude/ longitude data into the column of Search and click on search button, Google Earth will display the position map for you,as following picture shows: - 25 -Page 25 of III More Professional SMS Instruction ****** is user password, and init password is SMS Instruction Format Note 1 Request one position W******,000 2 Modify user password W******,001,###### ****** is old password ###### is new password 3 Set the time internal of position refresh 4 Set a preset phone number for SOS button When this button is pressed, VT300 will dial the preset number. 5 Set low power alarm When the Vt300 voltage is lower than the preset value, Vt300 will send one lower power alarm SMS to the SOS preset number. W******,002,XXX W******,003,1,1,TelNumber XXX(3 digital) =000,stop =[1,999] time internal (unit: mins) TelNumber: Preset Tel number (TelNumber must 16 digits ) W******,004,X X (voltage preset value) =0, close =1, 3.3V send SMS alarm =2, 3.4V send SMS alarm =3, 3.5V send SMS alarm (default ) =4, 3.6V send SMS alarm =5, 3.7V send SMS alarm 5 Set over speed alarm When the Vt300 speed higher than the preset value, Vt300 will send one over speed alarm SMS to the SOS preset number. W******,005,XX XX (the speed preset value) =00, close =[01 XX 20] (unit: 10Km) 6 Set Geo-fence alarm When the VT300 move out preset scope, Vt300 will send one Geo-fence SMS to the SOS preset number. W******,006,XX XX ( preset distance to original place ) =00 close =01 30m =02 50m =03 100m =04 200m =05 300m =06 500m = m = m 8 Extend setting (note: Please use this instruction carefully) W******,008,ABCDEFG### Page 26 of A=0, Close position report function which get position SMS by Calling VT300 A=1, Open position report function which get position SMS by Calling VT300 B=0, position SMS format be analyzed in order to read easily. For example: Longitude = 114 degree - 04 cent second Latitude = 22 degree - 32 cent second B=1, position SMS format is NMEA 0183 Format For example: $GPRMC, ,V, ,N, ,E,0.00,0.00,050805,*00 C=0, Vt300 do NOT hung up when one call incoming. C=1, VT300 hung up after 4~5 rings when call incoming D=0, VT300 do NOT send one notice SMS to SOS preset number when the GT30 power on D=1, VT300 do send one notice SMS to SOS preset number when the GT30 power on E=0, VT300 do NOT shut down automatically when the power voltage lower than 3V E=1, Vt300 will shut down automatically when the power voltage lower than 3V F=0, Vt300 do NOT send the notice SMS to the SOS preset number when the GPS signal is weak F=1, Vt300 send the notice SMS to the SOS preset number when the GPS signal is weak ###, end char (default value should be : ABCDEFG= ) 9 Set sleep mode for saving power. W******,021,XX### Page 27 of XX=00 close sleep mode XX=01 sleep XX=02 deep sleep GPRS setting 9 Set the phone number for VT300 for GPRS W******,010,tel tel : telephone number according the SIM card of GT30 (tel must be 14 digits) 10 Set APN W******,011,APN APN : APN string 11 Set IP Address &port number W******,012,IP,PORT IP: xxx.xxx.xxx.xxx PORT: [1,65536] 12 Open / Close GPRS function W******,013,X X=0 close GPRS X=1 open GPRS - 28 -Page 28 of IIII GPRS communication setting step1: make sure that your SIM card in VT300 have the GPRS faction Step2: Set the phone number of VT300 by send one SMS: SMS Format: W******,010,tel For example : W000000,010, VT300 will response one SMS to check it. 123 can be considered to be the device s name. (Tracker ID must be 14 digits) If there are several devices,you can use their Tracker ID to differ from each other. VT30 will response one SMS to confirm the setting. Like set SIM OK/120 Step3 : Set IP address and Port by send one SMS SMS Format: W******,012,IP,PORT For example : W000000,012, ,8000 Make sure that the IP should be the Extranet IP. If your pc is in Intranet,you must know your Extranet IP. You can know your PORT from the router s configuration. Now there are two ways of getting your IP address and PORT: First,you can get your IP and port through the DOS Order: ipconfig. Second, the IP address and PORT can be got from IT supports, such as some IT support websites.. FORMAT: IP: xxx.xxx.xxx.xxx PORT: [1,65536] For example : W000000,012, ,8000 VT300 will response one SMS to check it. Like Set IP ok / #8000 Step4: Set APN SMS format : W*****,011, APN APN is your username when you use the GPRS function,and it is used to be connected to the intenet. - 29 -Page 29 of For example : W000000,011, CMNET Step5: Enable GPRS function SMS format: W******,013,X For example: W00000, 013, 1 VT300 will response one SMS to check it. Like set APN OK /CMNET ( Note: 1 VT300 default value is GPRS Disable 2 SMS W0000,013,0 is disable GPRS function ) Step6 : According to GPP communication protocols of VT300, the server can analyses the GPRS data. Or According to NMEA V3 protocol, the server can analyses the GPRS data. - 30 -Page 30 of IIIII DIY!!! Build your control center system on your PC We provide one low cost solution help you build your control center system on your PC, which is very cheaper than other center system. You NEED: ---- ( very low cost) (1) Google Earth Plus ( ) Or any other navigation map software (PC version) (2) one PC (3) RT200 SMS modem ( provided by us) (4) RView TrackMaker software on PC (provided by us freely) (5) Some VT300 ( provided by us) System structure - 31 -Page 31 of Software Interface Google earth One navigation map software - 32 -Page 32 of - 33 -Page 33 of Attachment :Worldwide APN (Access Point Name) List - 34 -Page 34 of - 35 -Page 35 of - 36 -Page 36 of - -Page of
Search Related
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks